#KASA SMART SWITCH WIRING HOW TO#

Turn the power back on and test the switch.The Kasa line also has smart light bulbs, security cameras and smart plugs. Attach the wall plate-some smart switches don't include a wall plate-you might need to buy it separately. Each Kasa Smart Switch is made by TP-Link, a company known for its routers, modems and other home networking devices.(It should come with screws, but you can repurpose the ones from the old switch too.) Fasten the switch in place with the correct screws.You can replace or extend the box with one from the hardware store, but old boxes aren't easy to remove without damaging the drywall. Know that smart switches are bulkier than normal light switches-don't try to force them into a box that's too small.Starting with the excess wires, push the new switch into the electrical box until it rests on the mounting holes.After attaching the wires, give them a little tug to make sure they're secure-you don't want them popping out as you push the wires and switch back into the gang box.If you're installing a lot of switches that don't come with connectors, then 2-conductor and 3-conductor lever nuts will make an easy, solid, safe connection.Many switches come with connectors like wire nuts and lever nuts to make the process easier.The switch may use slots, screws, or multicolored wires to attach to your wiring setup.Attach the wires to their corresponding spots on the smart switch-the majority of switches will have labels on the switch, but you can also find a diagram in the user manual.Installing the smart light switch is essentially the reverse of removing the old switch: Quick tip: If you see only one bundle of wires coming from a single side of the switch box (even if one wire is white), you don't have a neutral wire.

#KASA SMART SWITCH WIRING HOW TO#

Traveler wire: If you see a red wire coming off the opposite side of the switch from the hot wires, it's probably part of a three-way setup, so your smart light switch might not be compatible. How To Install A Kasa Smart Switch (HS200) That Works With Alexa One Hour Smart Home 64K subscribers Subscribe 171 Share 64K views 2 years ago Kasa Smart Switch.Ground wire: The ground wire is usually a green wire or plain copper wire that attaches to another screw on the metal part of the switch.

It's neutral because it doesn't connect to the switch and carries the current back to the breaker to complete the circuit. Check to make sure the switch instructions dont specify 'line' and 'load' on the wires.

Neutral wire: The neutral wire is usually a gray or white wire-often two wires with a wire nut in the back of the gang box. Wire nut the two black wires in the box to one black wire from the switch.

The top screw (closest to the switch's on position) is the load wire, which comes down from the light fixture-it's often a black wire but can be red.

Use voltage tester to confirm no voltage is present.

The bottom screw (closest to the switch's off position) is the line wire, which comes up from the circuit breaker. Step 2: Turn off power at the circuit breaker that controls the light switch.

Turning the switch on connects the two wires to allow an electrical current to flow up to the light fixture.

Hot wires: One side of the outlet will have two screws holding two black wires.

Light works with regular switch.Gently pull out the existing switch so you can look at the wiring. Reinstalled the Kasa (checking carefully to make sure the connections were solid) but the light still doesn't turn on. I pulled the Kasa and put the mechanical switch back in and the light works as it should. However, the light the Kasa is connected to doesn't come on. I can use my phone or press the Kasa to operate the Kasa, and I hear a click from the Kasa and see the indicator on the Kasa switch states. I connected the Kasa to my network with no problem. On the Kasa, I tied the white wire to the existing white wire, the existing black wire to one of the black wires on the Kasa, the existing red wire to the other black wire on the Kasa, and the green wire on the Kasa to the existing bare copper ground wire. The machanical switch wires were connected as follows (looking at the wall): Black wire to top right connector on switch, white wire to bottom right connector, red wire to top left connector. The existing installation has 4 wires - black, red, white and bare copper ground. I want to install a Kasa HS200 in place of a mechanical switch to operate a ceiling light.

Kasa smart switch wiring